Arizona Registrar of Contractors ROC License# ROC 328433
Cleaning Tips

Tips To Help You Succeed in Your Own Home

There are a few basic procedures that are efficient and save time which any one can follow. Determining the surface composition before starting the cleanup procedure.

Surface Skimming

Dirt floating on the surface of the water is easier to remove than to remove it from the bottom. Remove floating debris off the surface, using a leaf rake and telepole. As the net fills, empty it into a trash can or plastic garbage bag. Do not empty your skimming debris into the garden or on the lawn for the debris is likely to blow right back into the pool as soon as it dries out.

There is no particular method to skim, but as you do, scrape the tile line, which acts as a magnet for small bits of leaves and dirt. The rubber-plastic edge gasket on the professional leaf rake will prevent scratching the tile.

If there is scum or general dirt on the water surface, squirt a quick shot of tile soap over the length of the pool. The soap will spread the scum toward the edges of the pool, making it more concentrated and easier to skim off.

Water Level

If you add an inch or so of water to the pool each time you service it, you will probably keep up with normal evaporation. If you wait a few weeks until the level is several inches low, it will take hours to fill. It is also important to maintain your water level so you don’t ruin your pump. Never leave the water on to fill by itself for it may take longer and most likely you may forget to turn it off.

After rains you might need to lower the pool level. In this case, use your submersible pump and a backwash hose or spare vacuum hose for the discharge. Alternatively, you can run the pool circulation system and turn the valves to waste. If you use this method, remember to return the valves to normal circulation.

Equipment Check

Checking your equipment and maintaining your support system is best way to solve the small corrective problems.

Start by circulation system by following the path of the water. Clean out the pool’s skimmer basket and Emptying the contents of the skimmer basket into your trash can or garbage bag.

Next, open the pump strainer basket and clean it. Check the pressure of the filter. There is no point in checking it before cleaning out the skimmer and strainer baskets, because if they are full the filter pressure will be low and will come back up after cleaning the baskets. If the pressure is high, the filter might need cleaning.

Now check the heater for leaves or debris. Turn the heater on and off a few times to make sure it is operating properly. While the heater is running, turn the pump off. The heater should shut off by itself when the pressure from the pump drops. This is an important safety check.

Now check the time clock for the time of the day ; setting for the daily filter runs; setting for the cleaner’s clock. Always check the clocks because trippers come loose and power fluctuations or some service work on household items unrelated to the pool can also affect the clocks. Also, electromechanical time clocks are not exactly precision instruments. One might run slightly faster than another, so over a few weeks one might show a difference of an hour or more, upsetting your planned timing schedule.

After the equipment check, look for leaks or other early signs of equipment failure. Clean up the equipment area by removing leaves from around the motor vents and heater to prevent fires, and clear deck drains of debris that could prevent water from draining away from the equipment during rain.

Vacuuming

If the pool is not dirty, simply brush the walls and bottom, skipping the vacuuming completely. If the pool or spa is dirty, however, you have two ways to clean it: vacuuming to the filter or vacuuming with the leafmaster.

Spa & Water Feature Cleaning

The steps outlined for pool cleaning will work just as well for spas and water features. Here are a few special tips about what you might encounter that is unique to these bodies of water.

Many spas are made of fiberglass, so take care when vacuuming to avoid scratching the surfaces.

Vacuum the corners of water features and small spas with the spa vacuum described earlier.

Evaluate the spa or water feature when you arrive, before you invest a great deal of time in cleaning. Test the chemistry first, so you can determine if you are better advised to drain the unit rather than clean and treat it. If the water or surfaces are very dirty, if the water is extremely hard or cloudy, if the dirt is in among rocks and gravel where it might be very hard to reach, pump out the water and clean the unit that way.

If you do drain a spa or water feature, be sure the equipment is turned off at the breaker so the time clock won’t turn it on before you are ready. You might need to set up your submersible pump and go to another job while the unit is draining. Your submersible has a small hole in the bottom to re-circulate the last inch of water to avoid burning out it’s seal, so you can let it run without worrying that it will run dry.

Before you clean the spa or water feature, clean the filter and run some fresh water (from the garden hose) through the circulation system to purge any dirty water from the lines. Nothing is worse than draining, cleaning, and refilling a spa only to turn the circulation back on and watch dirty water contaminate your work.

Be extra careful with chemical testing and application. Most spas and water features contain a tiny fraction of the volume of water in a pool, so they can’t absorb a mistake the way a pool might. It is better to add chemicals more slowly and in less quantity than you think necessary. You can always add more, but it is a real problem to remove any excess.

Water Testing and Application

Follow the general testing guidelines needed, testing for chlorine residual, pH, total alkalinity, and acid (or base) demand, calcium hardness or total hardness and total dissolved solids should be conducted one a month.

Call Us Today
480-430-8129

N

Pool Cleaning Services

N

Full Service Maintenance

N

Professional Pool Repairs

N

Monthly Billing Available

We use Angie’s List to assess whether we’re doing a good job keeping valued customers like you happy. Please visit Angie’s List in order to grade our quality of work and customer service.

(480) 430-8129
Mesa, Arizona